PAS · Energy registers, water and gas
Gas meters: m³ totals and the boundary between volume and energy
Configure the pulse-volume meaning carefully, and distinguish measured gas volume from corrected volume and gas energy.
Written course for development review; live pulse commissioning and recording pending.
Before you start
- Identify the exact model, firmware and fitted input modules. A PAS source list does not prove that every input exists on the meter.
- Read and save the current setups and required logs before changing sources, multipliers, tariffs or counters. Use an authorised training setup for programming exercises.
Identify what the gas output represents
A gas meter or volume corrector may supply pulses for measured operating volume, volume corrected to stated reference conditions, or another explicitly configured output quantity. Obtain the actual output configuration and pulse constant. The word gas does not establish which quantity is present.
Record source identity, output channel, volume basis, units, pulse constant and any external corrector. Match the electrical output to the fitted input using both manufacturers’ instructions. PAS does not determine gas reference conditions from the shape of a pulse.
Worked gas-volume example
Assume the external output is explicitly configured for 0.1 m³ per pulse. This example’s source is volume, not energy. The reciprocal description is 10 pulses/m³.
A raw-count increase from 12,040 to 12,113 is 73 pulses. Volume increment = 73 × 0.1 = 7.3 m³. Over exactly 30 minutes, the calculated average volume rate is 7.3 ÷ 0.5 = 14.6 m³/h. This is an average over that period, not an instantaneous flow measurement.
Apply the same source-to-total checks
In PAS, inspect MeterSetup > General Setup > Digital Inputs for the fitted channel, then MeterSetup > Energy/TOU for its assigned source, target register, volume multiplier and unit. Use the fractional billing multiplier where required rather than rounding a fractional volume into an integer event counter.
For the example, the volume multiplier is 0.100 m³ per pulse. Keep the original setups and total, read back any authorised change and compare a known pulse increment. Keep water and gas on distinct source assignments with unambiguous names where the selected model supports names.
If the external output is specified in cubic feet, do not select m³ and leave its numerical factor unchanged. Convert the physical volume per pulse first, document the conversion and verify the resulting increment. CF means cubic feet; CCF means one hundred cubic feet.
A volume unit is not an energy calculation
m³ and kL are volume units. MJ and kWh are energy units. Choosing the XM MJ label does not supply gas composition, calorific value or pressure/temperature correction. It cannot turn an uncorrected volume pulse into a defensible energy total by itself.
Conceptually, gas energy requires volume on the specified basis multiplied by the applicable energy-per-volume factor, with the required correction method. If an external corrector already supplies corrected volume or energy pulses, document that fact and avoid applying the correction a second time.
This course does not prescribe a gas billing conversion, a universal calorific value or an approved billing arrangement. Obtain the application’s defined quantity and conversion from the responsible gas metering/provider documentation before configuring an energy total. A unit option in an electricity meter is not evidence of gas billing approval.
Allow for pulse resolution and missing pulses
A coarse pulse constant produces stepped totals. Short periods can contain no new pulse even when a small volume has passed. Select the observation period to obtain a meaningful pulse count and retain the original cumulative readings.
If a pulse is missed, changing the multiplier does not recover when that volume occurred. Compare source and receiving-counter increments over the same period, preserve the discrepancy and resolve the signal, input or configuration cause before trusting new history.
Limits and checks
- Worked values are teaching examples, not readings or settings from the demonstration meter. No live programming or pulse test is represented by this written lesson.
Check your understanding
Can you convert water or gas m³ to kL?
Show answer
Yes: 1 m³ = 1 kL. That volume equivalence does not convert gas volume into kWh or MJ.
Sources
- Source 1. EM13x Installation and Operation Manual — Billing/TOU (opens in a new tab)
Printed pages 114–118 / PDF pages 117–121. Base-family procedure; XM capacity and units require the XM reference.
- Source 2. EM133 / EM133-XM Modbus Reference — volume units (opens in a new tab)
BG0640 Rev. A1, PDF/printed page 80, F15: m3, CF, CCF; kL and MJ are XM entries.
- Source 3. PRO Series Installation and Operation Manual (opens in a new tab)
BG0612 Rev. A8, December 2024. PDF/printed pages 10–12 (modules), 64, 80, 118 and 138–139. Some appendix/target tables differ; use the current protocol alongside the main chapters.
- Source 4. PM180 Operation Manual (opens in a new tab)
BG0525 Rev. A7, April 2019. Printed pages 9, 22, 75 and 117–118 / PDF pages 10, 23, 76 and 118–119.
- Source 5. EM13x Installation and Operation Manual — digital inputs and counters (opens in a new tab)
Printed pages 100–101 and 105–106 / PDF pages 103–104 and 108–109.
Revision and review details
| Revision | Change and reason | Review / supersedes |
|---|---|---|
| 20261108-energy-v1 8 November 2026 | Added electricity-first energy and water/gas pulse-register lessons. Explain model-specific capacity, correct units, PAS setup and consumption checks. | Primary-source and configured Product Master consultation completed; independent artifact review follows. None |